►CLICK HERE to grab it from the SEREV3d Current download links board (Accessible for active paid members)

INFO:

We tried to make our seraphim angel design as biblically accurate as possible ,it has a hollowed inside, so it can be perfectly used as a Christmas tree topper!
It’s a quite easy print, it requires minimal amount of supports under the first 3 wing parts.
We provided a single and multicolor 3mf version too!

Print difficulty level: Beginner to Intermediate

“STEAL THEIR LOOK!” instructions:

Version1: Handpainted

Filament: Polymaker PLA Matte White

Craft glass eyes: 100PCS Eyes Glass Cabochon Eyes (12mm and the middle 4 ones are 16mm)

Filler Primer: Rust-Oleum Filler and Sandable Primer Spray 

Sandpaper: 3m Pro Grade Grit: 120, 3m Pro Grade Grit:220, 3M Wet or dry Sandpaper Grit: 600
 and/or Bates- Sandpaper, 18 Pack, 12 Grits, 120 to 3000

Primer: Rust-Oleum Painter’s Touch Spray Paint White

Paint: Fantastory Craft Acrylic Paint Set (Use white, grey, black, orange, and you can add a little bit of blue too)

Clear coat finish: Rust-Oleum Matte Clear Coat or if you want glossy look Rust-Oleum Clear Gloss

Glue: Gorilla Super Glue Liquid

  • Post-processing steps (if you don’t mind the layer lines being too dominant, you can skip the sanding part, and jump right to the primer coat and painting)

    • Sanding: Start with coarse sandpaper (120 grit) to smooth layer lines, then use finer grits (220) and lastly (400-600) for a more polished surface.

    • Filler Primer: Apply a filler primer coat to cover imperfections. Let it dry completely.

    • Wet Sanding: Use 400-600 grit sandpaper for wet sanding the primer, repeating as needed for smoothness.

    • Final Primer Coat: Apply a thin layer of regular primer to create an even base for painting.

    • Painting: Paint with your chosen color from the acrylic paint set (grey, silver, white)

    • Finish: Seal with Rust-Oleum Matte Clear Coat for a subtle finish or Clear Gloss for a shiny effect.

    • Attach Eyes: Attach the glass eyes with Gorilla Super Glue Liquid.

(Allow each layer to dry fully before moving to the next for the best results.)

——————————

Version2: Gradient T-PLA

Filament: ZIRO Blue-White T-PLA Filament

Craft glass eyes: 100PCS Eyes Glass Cabochon Eyes (12mm and the middle 4 ones are 16mm)

Glue: Gorilla Super Glue Liquid

Steps:

  • Print with gradient translucent filament: you can try different gradient shift techniques, if you print even more angels all at once, the gradient shift is more dominant, if you print less, the gradient shift is bigger & more subtle.

  • Attach Eyes: Attach the glass eyes with Gorilla Super Glue Liquid.

===========================

Recommended print settings:

(If you use Bambu or Orca slicer, all the print settings are automatically loaded in each version’s 3mf files)

–Layer height: 0.2mm, if you want less thicker layer lines you can set it to 0.16mm (Or even lower, or turn on Adaptive Layer Height if you want very minimal visible layer lines, but it will increase your printing time)

–Wall loops: 3

–Infill: 10-8%, Gyroid

–Supports: Add Tree supports only under the 3 bottom wings, with a TopZ distance 0.28, BottomZ distance 0.2 (as shown on the picture)

►CLICK HERE to grab it from the SEREV3d Current download links board (Accessible for active paid members)

———————–

Have fun, we are looking forward to see your 3d prints!

Don’t forget to show off your awesome makes on 

►Our Patreon chats: https://www.patreon.com/serev3d/chats

►Or in our SEREV3d facebook group: https://www.facebook.com/groups/1569100737016945

Other popular 3d print groups to show off your makes:
–3d Printing for Beginners and Pros
–3D Printing ⚙️
–Bambu Lab 3D Printer Group